<div dir="ltr"><div>Hi,</div><div>I'm Lai, master research student from University Malaya, calibrating data using MOJAVE raw data BG173b. I'm using AIPS version 31DEC20. The OPACOR keep running into this problem:<br></div><div>APCAL1 17:23:17 Task APCAL  (release of 31DEC20) begins<br>APCAL1 17:23:17 TXTWX: Weather data read from WX table   1<br>APCAL1 17:23:17 Writing SN table   2 for subarray  1<br>APCAL1 17:23:17 BR       RCP 0/19h 1m Trec (K):    47.36 Zen. opac.: -0.011<br>APCAL1 17:23:17 OPACOR: ERROR:BR  RCP Tau0 (K),  -0.01, unreasonable value.<br>APCAL1 17:23:17       --This is probably due to bad data in TY table,<br>APCAL1 17:23:17         do some editing and try again.<br>APCAL1 17:23:17 Purports to die of UNNATURAL causes<br>APCAL1 17:23:17 localhos 31DEC20 TST: Cpu=      0.0  Real=      0  IO=         3<br><br></div><div>Tsys looks fine and it should get a fit. This problem remain when I try with another set of data BL137. For BL137 I then use opcode 'GRID' and manage to get it run without error, but return Zen. opac=0 for every antenna. For BG173b none of the opcode works, 'GRID,GRDR,OPAC,OPCR,LESQ', all failed with the same negative zen. opac problem. I also tried with 31DEC19, but the same happens. <br></div><div>I saw a thread in daip that is posted by Lister, M., "problems with APCAL', where his seems to describe the same problem as mine. But the thread ended abruptly. I guess that would be helpful for me.</div><div>Below is my adverbs:<br></div><div><br></div><div>AIPS 1: APCAL     Task to generate an amplitude calibration SN table<br>AIPS 1: Adverbs     Values                 Comments<br>AIPS 1: ----------------------------------------------------------------<br>AIPS 1: INNAME     '070927'                Input UV file name (name)<br>AIPS 1: INCLASS    '7GHZ'                  Input UV file name (class)<br>AIPS 1: INSEQ         1                    Input UV file name (seq. #)<br>AIPS 1: INDISK        1                    Input UV file disk unit #<br>AIPS 1:<br>AIPS 1: ANTENNAS   *all 0                  Antennas to calibrate<br>AIPS 1: SUBARRAY      0                    Subarray 0 -> all<br>AIPS 1: STOKES     ' '                     Stokes type ('R','L',' ')<br>AIPS 1: BIF           1                    Start IF number<br>AIPS 1: EIF           4                    End IF number<br>AIPS 1: FREQID       -1                    Freq. ID to calibrate<br>AIPS 1: SOURCES    *all ' '                Sources to calibrate<br>AIPS 1: TIMERANG   *all 0                  Time range to calibrate<br>AIPS 1:<br>AIPS 1: TYVER         1                    TY table version number.<br>AIPS 1: GCVER         1                    GC table version number.<br>AIPS 1: SNVER         2                    Output SN table version.<br>AIPS 1:                                      0 -> highest unique<br>AIPS 1:                                      appends to existing file<br>AIPS 1: OPCODE     'LESQ'                  Opacity correction opcode:<br>AIPS 1:                                    '    ' -> no opacity corr.<br>AIPS 1:                                    'GRID','GRDR','OPAC','OPCR',<br>AIPS 1:                                      'LESQ' -> fit for opacity<br>AIPS 1:                                    'PLOT' plot input fit<br>AIPS 1: APARM      *all 0                  Calibration parameters:<br>AIPS 1:                                    (1) -> B factor (def. 1.0)<br>AIPS 1:                                    Opacity parameters:<br>AIPS 1:                                    (2) -> ZA limit (deg)<br>AIPS 1:                                    (3) >=0  use spillover<br>AIPS 1:                                             correction<br>AIPS 1:                                    (4) > 0  use all FQ in<br>AIPS 1:                                             opac. soln.<br>AIPS 1:                                    (5) Limit to sec(z) plotted<br>AIPS 1:                                    (6) > 0 => normalize Tsys<br>AIPS 1:                                        by average Tsys<br>AIPS 1:                                    (7) Use IF AP(7) for<br>AIPS 1:                                        normalization instead<br>AIPS 1: SOLINT        0                    Solution interval (min)<br>AIPS 1:                                       0 -> use all data<br>AIPS 1: INVERS        1                    WX table version number.<br>AIPS 1:                                       0 -> use text file<br>AIPS 1: CALIN      *all ' '                Text file with weather info.<br>AIPS 1:                                       Must be ' ' if using WX<br>AIPS 1:                                       table (INVERS).<br>AIPS 1: TRECVR     *all 0                    Receiver temperatures (K);<br>AIPS 1:                                       in (R,L) pairs.<br>AIPS 1: TAU0       *all 0                  Zenith opacities (per ant.)<br>AIPS 1: DOFIT         1           1        Fit type (per ant.)<br>AIPS 1:               1           1          -1 -> no opacity correction<br>AIPS 1:               1           1           0 -> apply TRECVR only<br>AIPS 1:               1           1           1 -> solve for Trec using<br>AIPS 1:               1           1                fitting method spec.<br>AIPS 1:               1           1                in OPCODE; then apply<br>AIPS 1:               1           1           1           1<br>AIPS 1:               1           1           1           1<br>AIPS 1:               1           1           1           1<br>AIPS 1:               1           1           1           1<br>AIPS 1:               1           1<br>AIPS 1: PRTLEV        1                    Print level<br>AIPS 1: DOTV          1                    TV selection (<0 -> PL file)<br>AIPS 1: LTYPE         3                    Plot labeling<br>AIPS 1: GRCHAN        0                    TV Graphics channel to use</div><div><br></div><div><br></div><div>Regards,</div><div>Lai<br></div></div>