>inp 
AIPS 1: VLARUN : Applies amplitude and phase calibration to VLA data
AIPS 1: Adverbs     Values                 Comments
AIPS 1: ----------------------------------------------------------------
AIPS 1:           ** Type RUN VLARUN to load this procedure **
AIPS 1: WORKDISK      1                    Working disk, thus in/outdisk
AIPS 1: CATNUM        0                    Catalog number of the UV-file
AIPS 1:                                     must be 'CH 0' for line data
AIPS 1: INNAME     '19860825'              Input UV file name (CATNUM<1)
AIPS 1: INCLASS    'L BAND'                Input UV file class(CATNUM<1)
AIPS 1: INSEQ         1                    Input UV file seq. (CATNUM<1)
AIPS 1: FASTSW        1                    > 0 Correct fast-sw source
AIPS 1:                                        names
AIPS 1: AUTOFLAG      2                    Level of automatic flags used
AIPS 1:                                    < 0: no automatic flagging.
AIPS 1:                                    = 0: default FLAGR
AIPS 1:                                    = 1: flag beginning of scans
AIPS 1: PHAINT        1                    phase solution interval (min)
AIPS 1: AMPINT        5                    ampl. solution interval (min)
AIPS 1: REFANT        9                    Reference antenna number
AIPS 1: DOMODEL       1                    > 0 Use standard flux
AIPS 1:                                        calibrator models
AIPS 1:                                    Note that most standard flux
AIPS 1:                                    calibrators have models but
AIPS 1:                                    the absence of a model will
AIPS 1:                                    make VLARUN CRASH. (see HELP)
AIPS 1: UVRANGE       0           0        UV range for flux calibrator
AIPS 1:                                    (set if no model)
AIPS 1:           ** use next 2 lines if flux calib. is NOT standard **
AIPS 1: AMPCAL     ' '                     Alternative flux calib. name
AIPS 1: FLUX          0                    Flux calib. total flux dens.
AIPS 1: PHACAL     '*'                     Phase calibrators
AIPS 1:            *rest ' '               '*' = any CALCODE (continuum)
AIPS 1:                                     All others are your targets
AIPS 1: BNDCAL     *all ' '                Bandpass calibrators (max 5)
AIPS 1:                                    *BNDCAL only used for LINE*
AIPS 1: NOPAUSE      -1                    > 0 no pause after GETJY
AIPS 1: AUTOPLOT     -1                    > 0 make diagnostic plots
AIPS 1:           ** the following lines are for auto-imaging **
AIPS 1: DOIMAGES     -1                    > 0 apply calibration and
AIPS 1:                                        image
AIPS 1: ARRYSIZE      0                    Max baseline in kilometers
AIPS 1:                                    = 0 let procedure find array
AIPS 1: IMSIZE        0           0        Square size of image (pixels)
AIPS 1: NITER         0                    Max number of iterations/chan
AIPS 1:                                    = 0 recommended for LINE
AIPS 1: CUTOFF        0                    Clean threshold (Jy)
AIPS 1: ALLIMG        0                    > 0 also image continuum
AIPS 1:                                        calibrators
AIPS 1:                                    > 1 line calibrators too
AIPS 1:           ** interactive self calibration mode
AIPS 1:                     -- not recommended for beginners **
AIPS 1: SLFCAL        0                    > 0 do interactive selfcal
AIPS 1:                                    ABS(SLFCAL) the number of
AIPS 1:                                       iterations
AIPS 1:                                    See HELP VLARUN and
AIPS 1:                                    EXPLAIN SCIMG
AIPS 1: BADDISK    *all 0                  Disks to avoid for scratch